Words: 1013
The change represents the difference in enthalpy of the products and the reactants and is independent of he steps in going from reactants from products. The second, is the heat of formation (Off), which is also known as standard enthalpy of formation, and is defined as the change in enthalpy that accompanies the formation of one mole of a compound from its elements with all substances in their standard states. The enthalpy change for a given reaction can be calculated by subtracting the enthalpies of formation of the reactants from the enthalpies of formation of the products.
This can be illustrated in this equation: . During this experiment, Hiss’s Law was a concept that the lab concentrated on. Hiss’s Law states that if a reaction can be carried out in a series of steps, the sum of the enthalpies for each step equals the enthalpy change for the overall reaction. For example, the three chemical equations used throughout the experiment were: Equation 1: Noah(aqua) + HCI(aqua) Nasal(aqua) + H2O(l) Equation 2: Noah(aqua) NH(aqua) +Nasal(aqua) + H2O(I) Equation 3: NH(aqua) + HCI(aqua) Enoch(aqua) Resulting in Equation 1 plus Equation 2(reversed) will equal Equation 3.
In this case, Hiss’s Law gave the AH for Equation 3. The last important concept covered in this lab is calorimeter. Calorimeter is the science of measuring heat, and is based on observing the temperature change when a body absorbs or discharges energy as heat. A calorimeter is the device used experimentally to determine the heat associated with a chemical reaction. During this experiment, a coffee cup calorimeter was used. The equation is associated with a calorimeter because it discovers the amount of heat produced by multiplying the mass of the substance by the specific heat and by the change in temperature.
Since the coffee cup calorimeter will absorb heat, the data must be corrected for that by solving for kcal and kcal. The value of kcal will be the opposite of , and in order to find the value of kcal, the equation must be used. Procedure: For Part 1, 50. 0 ml of distilled water at room temperature needs to be measured, its initial temperature recorded, and placed into the calorimeter. Then, 50. 0 ml of heated water will need to be measured, its initial temperature record, and placed into the calorimeter with the room temperature water.
With the motor on and the magnet spinning, immediately insert the thermometer probe and collect the data. For Part 2, 50. 0 ml of HCI and Noah needs to be obtained and heir initial temperatures recorded. Then add them to the calorimeter, cover the calorimeter, insert the temperature probe, and start collecting the data. Do this procedure for Reaction 2 and Reaction 3. Then, the heat change and enthalpy of reaction are to be calculated. The value of AH is to be found two ways, through experimental data and using Hiss’s Law. These values are then compared to find the percent error of the experiment.
Like the error before, it would have a small effect on the data that was reduced. The second error was that the initial temperature measurements for all solutions were not the same. For example, in the first reaction of Part 2, the initial temperature of hydrochloric acid was 24. 5 co and the initial temperature of sodium hydroxide was 23. 9 co. In order to find the initial temperature, the average of these two numbers had to be taken, which could have caused the calculations to be slightly higher or slightly lower than what they should have been.
However, this error would have a minor effect on the data since there is to a large difference between the numbers. The third error that occurred in the experiment was that too much or too little water could have been added to the solution in the process of mixing the molar solutions. This could have increased or decreased the military of the solution trying to be made. This would affect the results but only in a minor way. Conclusion: The purpose of this experiment was met because the group was able to verify Hiss’s Law. From the calculations, AHA was found to be -26 k/mol, and when Hiss’s Law was used, AHA was found to be -18. J/mol. The percent error calculated from these values ended up being -39. 78%. Since the calculated answers were close, the purpose was met. Questions 1. The direct method worked better to find AHA than the indirect method because in order to use Hiss’s Law, the data had to be nearly error free. If the group does have an error in the calculations, than the Hiss’s Law answer will not match the answer the group calculated. The Hiss’s Law answer had a -61% error compared to the calculated answer. Therefore, the direct method worked better than the indirect method. 2.
Hiss’s Law states that if a reaction is carried out in a number of steps, AH for the overall reaction is equal to the sum of the ASH’S from each individual step. 3. AH means the heat or enthalpy change for a chemical reaction. This energy change is equal to the amount of heat transferred, at constant pressure, in the reaction. This change represents the the steps in going from reactants to products. 4. The true initial temperature is found by using a modified linear fit because when excluding any points that are skewed, it is giving the results a more accurate reading.
The first couple points that were skewed are due to incomplete mixing and lack of equilibrium with the thermometer. 5 All of the solutions did not have the same initial temperature because they were not contained in the same area of the room. These areas could have a slightly different temperature causing the different initial temperatures. Also, transfer of heat from holding the graduated cylinder could have increased the initial temperature, and depending on how long the graduated cylinder was held, could have determined how high the initial temperature rose.